Wednesday, May 30, 2012

How to Retrofit an EV conversion to J1772 in 7 easy steps


Over the last 6 months or so, more and more  public charging stations have been installed around town so I finally decided it was time to join the J1772 club. For those of you not familiar with the term, J1772 is the designation for the plugs and inlets that are the official standard for EV charging in the US. With the standard connection on my car, I could take advantage of these charging spots - and many of them are free. 


My old charger port was a L6-20 which was cheap and fine for charging at home, but few public places had this style connector waiting for me... It had served me well over the last 4 years, but change is good.


Most of the local stations I ran across were from Coulumb, so I set up an account at ChargePoint and got a $5 card for using their chargers. How's that for thinking ahead?



Original L6-20 charging port


The whole process of installing the J1772 was easier than you'd think. Here are the steps I took:

Step 1 - buy a J1772 Inlet. The Inlet is the part that goes on the vehicle. I also needed to buy the plug end so that I could convert my home charging gear (a.k.a EVSE or Electric Vehicle Charging Equipment)  to J1772 also. There are a few places that sell these parts - and they aren't cheap, btw. I bought mine from TucsonEV . I had a few questions which they promptly answered and they were quick to replace a pin which wasn't correct from the factory - no complaints.


Step 2 buy resistor(s) and diode. The J1772 standard expects to see signalling between the charger and the outlet in order to power up the connection. Here's a link to a description of the electronics for the signalling involved.  Your charger is probably like mine in that it doesn't have a way to provide these signals. One could wire up a switch to manually provide the signalling, or buy a circuit board to to fake it out, or you could do like me and hard wire it so the EVSE thinks the charger is always ready and turns on the juice. This is a low voltage, low current application, so the parts are cheap and should be readily available. You need a diode that will handle 20ma and 856 to 908 ohms worth of resistors. I couldn't find a 900 ohm resistor so I used a 560 and 330 in series. These parts came to about $6.00 at 'the shack."
  
Parts needed -J1772  Inlet, diode and resistor(s)
Step3 remove old inlet and test fit the new I pulled out the old inlet and disconnected the wiring from it. Then I dropped in the new J1772 unit in it's place. The screw holes for the old inlet didn't match the J1772, but to my surprise, the holes for the original Miata gas filler neck did! This made the swap real easy. If you aren't this lucky, you'll need to drill the mounting holes for your new inlet.


Step 4 Soldering the power pins Disassemble your inlet and figure out where the wiring needs to be placed for proper assembly. Mine had a pin retainer that needed to be over the wires before the pins were soldered on. I added a short wire to the ground so that I could easily connect the resistors and diode later. The power pins took a lot of heat to get up to temperature - more than my soldering gun would put out. I ended up using a butane plumbers torch at a low setting to warm up the pins. I tinned both the wire and the pin and then mated them together one at a time. 



Step 5 solder the pilot pin connection The pilot pin is the small one on the lower left. The one on the right is the proximity pin, which I understand isn't used. Connect your resistor(s) in series (end to end) with the diode. The stripe on the diode should go toward the ground wire. Solder one end of the component is soldered to the pin and the other end to the ground wire we put in earlier. It doesn't matter which order the parts go in as long as the diode is properly oriented.  Once you solder it, shrink tube it or tape it up and insert the pin in place. 


Step 6 Install the inlet assembly  Time to put the whole thing back together. Make sure the wires don't bind and a properly held in place by strain relief nut on the back.



Inlet installed - I later rotated it 90 degrees to allow the cord in my garage to connect easier
Inlet with cover and strain relief installed from inside the turnk

Step 7 test it out Drive out to your local charging station and plug in. Mine was at a Walgreens Drug store. Though the lot was full, the EV spot was empty, so I pulled in, plugged in and waved my little ChargePoint card in front of the charger. I heard a click and then the sound of the  charger in my car starting up - sweet.


Free parking and a free charge - Life Is Good!