The meltdown

Is it better to be smart or careful?
In my case, I was neither, or maybe I'm guilty of thinking I was smart, and careful.

I'm not sure exactly how it happened, but I do know that I had my cables laid out on the batteries on the nose rack. I had made the cable from most positive (the + terminal at the beginning of the string) to the the Zilla B+ terminal and the cable that connects the nose rack to the motor rack. I was measuring the cable that interconnected two terminals of the motor when it happened.

There was a loud snap.
Sparks flew.
Smoke filled the air.
And the smell of something burning.

I quickly pulled a sparking cable off the battery rack it was touching, and it stopped.
After the smoke cleared the cursing began.

Evidently, the Zilla cable that was just set in place slid off the terminal and touched the rack. A 5/8" open end wrench qas touching the rack and a cable. Enough of the cables made contact to complete a dead short across the batteries frying one of them. The terminal was melted away, as was a piece of two cable clamps and my 5/8" wrench. There was what appeared to be gray paint splattered around, but it wasn't paint, it was the lead post that vaporized.

I would like you all to think I'm brilliant and don't make mistakes, but in reality, neither is true. I make mistakes just like everyone else. So the message for this post is: don't be smart or careful, be safe. Don't think it won't happen to you or that you can just be careful - avoid the situation entirely by not taking chances - be safe.

It takes a village...

Sorry for the cornball title, but I wanted to mention something about the EV community. There are a lot of knowledge people out there willing to help answer your questions, loan you a hand or, in my case, a tool. I've gotten to the point where I need to start making up the high power cables - these are the ones that connect the batteries together in one long series string and connect up the main contactor, fuse, breaker and controller. To make these cables, you buy a roll of fat cable (I used 2/0 welding cable), some terminals (lugs and/or cable clamps) and then crimp them on the cables. A special tool called a cable crimper is needed to do this. You can get an inexpensive hammer crimper for $35 all the way up to a ratcheting hex crimper for around $300. In my research found that most people recommend the hex crimper (the ratcheting part is a nice addition, but not necessary) - but these run well over $200 and how often are you going to use it? Since I belong to my local EAA (Electric Auto Association), I decided to see if I can borrow one from a fellow member. I was overwelmed at the response. People offered to deliver it to my home, to meet me after work, to come over and help me crimp the cables over the weekend - amazing!
So I was able to borrow this expensive and amazing tool from a fellow EVer, no questions asked.

The crimping was kinda fun. The tool takes some muscle, but the results were clean and professional looking - if I do say so myself.

No more Zillas?

Big news today - Otmar is calling it quits. He evidently is having health problems related to running his business and looking to sell out.
Zillas are generally regarded as the best DC EV Controllers available. I would hope that someone reputable will take it over and keep these outstanding products on the market.

Read all about it on the Cafe Electric Blog:
http://www.cafeelectricpress.com/blog/?p=45

Keeping busy

My family was out of town tonight. Do you think I read a book, or watched some of the Olympics?
Nah, I worked on the car...
First I mounted the potbox - this is the electronic throttle that tells the controller how much juice to give the motor. I mounted it on the firewall behind the windshield washer reservoir. I thought about a number of ways to connect the accelerator cable to the lever and ended up using an electrical lug crimped to the cable. I then wrapped the extra cable around the mounting screw and attached it to the lug with a mini cable strap - this gives me a little reassurance that if the crimp comes loose that the cable loop will keep it working. Furthermore, since I didn't remove the end cap from the cable, if the crimp comes loose AND the mini strap breaks, the end cap won't get pulled through the lug, keeping the potbox working, though not as well.
Redundancy is good - double redundancy is even more gooder.
Sorry - I took the picture before I did the double redundancy stuff.

Next I drilled out the temperature sending unit so that it would fit under one of the Zilla's water fittings. The sending unit comes with a 1/4 lug, but I needed it to be 3/8". A little drilling, a little filing a and a little Dremeling and voila.

Lastly, I flipped the cover over on the Zilla so that the graphic was right side up. I know, but it was bothering me.

That's enough for one night.

brackets and mounts

Saturday I got to do a little bending and welding to finish off the mounts for the Iota and the Zilla, plus I got the battery straps mounted on the motor/cowl rack.
I wanted to attach the Zilla using a separate bracket so that other brackets could be used if another controllers was called for. The braket mounts to the rack, one of the rack brackets and a miata hole near the shock tower. I used flat head machine screws to that the bolt heads wouldn't interfere with the Zilla.
The Iota was originally going to mount with a bracket, but after some experimenting I found it could fit against the passenger side of the rack really nice. I welded up 4 tabs for it on the rack and drilled them out for flat head machine bolts so that the bold heads won't gouge the batteries.
Lookin' good.

Survey results - first pass

This morning I decided to see how the Conversion Kit survey was going.
I had 49 responses so far with the majority (45%) going with my components (156v, WarP 9, Zilla...) and 59% of those went with the Optima battery option. I'll take that as a vote of confidence - or maybe I was just lucky. This group was pretty split between the Basic kit at 38% and the Complete kit at 54%.

The runner up was pretty interesting... actually something I was considering for my next conversion...
39% of the votes went for an AC system from Selectria and the majority of the battery votes (47%) of this group went with Lithium. A good number (37%) went with Optimas.
Interesting...

There is still time to get your vote counted in the survey, and it only takes a few seconds (because there are only 3 questions). Just click here.

Iota is here

Got a big box today with a little 45 amp Iota in it. It's smaller than I thought, ought to be easy to find a spot under the hood for it. That's a dime on top of it so that you have an idea of the size.
By the way, I was going for their 30 amp model, but found a place that was selling the 45 amp model for about $135 - $15 more than the 30 amp model. This was about half what I thought I'd be paying, so why not go for the more powerful unit?